Sagging Mattress and Body Impressions: Causes and Fixes
Every mattress shows where you sleep. The question is whether you are looking at normal body impressions, which come with use, or a sag, which means part of the mattress is no longer supporting you. This page shows how to tell them apart, how to measure, what causes each and what you can do, including how to make a warranty claim.
Body impressions or sag?
| Body impressions | Sag | |
|---|---|---|
| What it is | The top comfort layers settle and shape slightly to your body | The support layers or springs have worn or broken down, or the base has given way |
| Depth | Shallow | Deeper, and often deepening over time |
| Feel | A gentle cradle where you lie | A dip you roll into, or a feeling of lying in a hole |
| When it appears | Often in the first months, then stabilizes | Usually later, or suddenly if the base fails |
| Usually covered by warranty | No, if within the depth the warranty calls normal | Often yes, beyond the depth the warranty sets |
Memory foam and pillow tops show impressions more readily than firmer surfaces, because their top layers are meant to conform.
How to measure it
- Strip the bed down to the bare mattress, protector included.
- Let it rest unoccupied for a few hours, ideally in the morning after you get up, so memory foam has time to recover.
- Lay a straight edge across the mattress at the dip. A long level, a straight piece of timber or a broom handle works; a tight string pulled across the width also works.
- Measure the gap between the straight edge and the deepest point of the dip with a ruler or tape.
- Repeat across the hip area, the shoulder area and anywhere else that dips, and note each figure.
- Photograph each measurement with the ruler visible.
Then read your warranty. It states the depth it counts as a defect and often how it must be measured, for example with no one on the mattress. The figure varies between makers.
Check the base first
A dip that appears quickly, especially in a new mattress, is often a base problem. With the mattress lifted off:
- Lay the straight edge across the base. Look for cracked or bowed slats, a center rail that has dropped, or a center leg that no longer reaches the floor.
- Measure the gaps between slats and compare them with what the warranty allows.
- On a box spring, look for broken wood or springs and a sagging middle.
If the base is at fault, fixing it may fix the mattress, at least partly. Our page on box springs, foundations and frames covers repairs. An unsuitable base can also give the maker grounds to refuse a claim, so it is worth fixing before you claim.
Why a new mattress can seem to sag
- Not fully expanded. A mattress delivered in a box needs the maker's full expansion time. Uneven areas often even out.
- Break-in. Foam comfort layers soften and settle during the first weeks. Shallow impressions at this stage are normal.
- The base. Wide slat gaps or no center support, as above.
- A genuine defect. A deep dip within weeks, on a proper base, is worth reporting to the seller straight away, especially within a trial period.
Why older mattresses sag
- Foam wear. Every foam loses some firmness with use; lower-density foams lose more, and faster. See foam density and ILD.
- Uneven use. One person sleeping in the same spot every night, or two people of very different weights.
- Never rotated. The same areas take all the load.
- Coil fatigue in innerspring and hybrid mattresses.
- Moisture and heat, which can weaken foam and adhesives.
What you can do
For body impressions
- Rotate the mattress head to foot every three to six months, or as the maker says, so different areas take the load. Flip it only if it is two-sided.
- Sleep in different spots now and then, if the bed is large enough.
- Add a topper if the impressions are shallow but bother you. A topper evens out the surface feel; it cannot fill a real sag. See mattress toppers.
For a real sag
- Fix the base first if it is part of the cause.
- Make a warranty claim if the depth is beyond the warranty's figure.
- As a short-term stopgap while you wait, some people place a thin, firm pillow or folded blanket under the mattress beneath the dip. It is not a repair, and some warranties may not accept it, so remove it before any inspection.
- If the mattress is out of warranty and the sag is deep, it is usually time to replace it.
Making a warranty claim
- Find the receipt and the warranty, and check that the law label (the tag that says it must not be removed except by the consumer) is still attached. Many makers require it.
- Measure as described above, in the way the warranty specifies.
- Photograph the sag with the straight edge and ruler, the whole mattress, the law label and the base.
- Note the base type and slat spacing, with photos.
- Contact the maker or seller and keep copies of everything you send and receive.
- Keep the mattress clean; stains can give grounds to refuse a claim, which is one reason to use a protector from the start.
Aches and a sagging bed
A sagging mattress can simply be uncomfortable to lie on, and comfort is a fair reason to fix or replace it. Persistent or worsening back, neck or joint pain, though, is for a doctor or physical therapist. A new mattress is a comfort choice, not a treatment. When the mattress itself is the problem, our page on when to replace a mattress lists the signs.